Magnetic Finishing presents itself as the pinnacle of methods to efficiently burnish and polish small non-ferrous metals. With media as small as .010 in diameter and .250 in length, these stainless steel pins are able to work in areas such as undercuts, recesses, slots, etc, where no previous method has been found suitable. Centrifugal Magnetic Finishing is quiet by comparison to many other forms of finishing. Typically on soft non-ferrous metals, the finishing cycle can be as low as 30 minutes. This alone assures faster turnaround time on parts when compared to any other method. Centrifugal magnetic tumbling as an automated process addresses the most intricate and detailed parts imaginable in finishes where others fail. It should be noted that on large, smooth or flat surfaces the finish will appear frosted and a slight buffing or a run in a dry finisher is recommended. 

What is a Centrifugal Magnetic Finisher?

The machine is a direct drive, fan cooled design. The magnetic disk is made up of many powerful magnets that are precisely placed in a cast disk. The alternating polarity is constantly changing, thereby allowing the media to move freely in a liquid solution that constantly changes its makeup. This, combined with centrifugal force, allows for super quiet and fast time cycles.

CMF-400

Raytech’s smallest capacity Magnetic Finisher has a 4"/ 100mm diameter chamber that finishes the equivalent of 8-10 rings. The machine comes complete with ample amount of pins and compound. Pin capacity is 100 grams. The CMF-400 has a fixed speed complete with mechanical timer and molded bowl & cover. Model CMF-400 has 1/32HP motor, 2.0 amps at 115V, 60Hz and 1.0 amps at 230V, 50Hz. Shipping weight is 17#, 1.0 cu ft.

CMF-400, 115V #23-048     [Add to Cart]  [View Cart]
CMF-400, 230V #24-139     [Add to Cart]  [View Cart]

CMF-610

Raytech’s Model CMF-610 is the former Model CMF-600. Designed to integrate programmable functions. Variable speed, forward/reverse. Timer functions are easily programmed to suit your cycle times. The Model CMF-610 has a 6"/150mm molded bowl with cover and carries a pin capacity of 200gms and a parts equivalent to 20-30 rings. Pins and compound are included. Model CMF-610 has a 1/12HP motor, 2.5 amps at 115V, 60 Hz and 1.25 amps at 230V, 50Hz. Shipping weight is 25#, 2.13 cu ft.

CMF-610, 115V #23-051     [Add to Cart]  [View Cart]
CMF-610, 230V #24-142     [Add to Cart]  [View Cart]

CMF-900

Raytech’s Model CMF-900 is designed to meet the needs of the larger size manufacturers. The bowl measures 9"/230mm and carries a pin capacity of 400gms (purchased separately) and a parts equivalent of 100 rings. The model CMF-900 is fully programmable and features variable speed and forward reverse functions. Model CMF-900 has a 1/3 HP motor, 4.0 amps at 115V, 60Hz and 2.0 amps at 230V, 50Hz. Shipping weight is 55#, 5.06 cu ft.

CMF-900, 115V #23-052     [Add to Cart]  [View Cart]
CMF-900, 230V #24-143     [Add to Cart]  [View Cart]

CMF-1200

Raytech’s Model CMF-1200 is the largest in the family of Centrifugal Magnetic Finishers. This model features a 12"/300mm diameter bowl and has a pin capacity of 800gms (purchased separately). It also carries all the same features and functions as the models 610 & 900. Fully programmable and features variable speed and forward/reverse functions. The CMF-1200 operates at 230V 50Hz/60Hz, 2.0 amps. Shipping weight is 85#, 9.18 cu ft.

CMF-1200, 230V, 50/60Hz #24-145    [Add to Cart]  [View Cart]

Magnetic Separators

Easy Parts Separation at your Fingertips for any Magnetic Finisher!! An Exclusive by Raytech!!

• Exclusive design by Raytech which eliminates tedious separation of parts from media.

• Magnetic Separators can be placed in water to separate the parts. No need to drain water as separator will not rust.

Models available:
Magnetic Separator 400/600 #23-081-Mates with
CMF-400 & CMF-600/610   [Add to Cart]  [View Cart]


Magnetic Separator 900/1200 #23-083-Mates with
CMF-900 & CMF-1200         [Add to Cart]  [View Cart]

Turbo Pins (3mm)-250gms #41-372  [Add to Cart]  [View Cart]
Turbo Pins (3mm)-1kg #41-374          [Add to Cart]  [View Cart]
Turbo Pins (5mm)-250gms #41-376  [Add to Cart]  [View Cart]
Turbo Pins (5mm)-1kg #41-378          [Add to Cart]  [View Cart]